How To Roll A Joint With A Filter

The "W" filter has quickly gone from a popular technique used among savvy joint connoisseurs to the industry-standard for cannabis retailers. Next time you lot're buying legal pre-rolled joints in states like California or Colorado, check the filter. It's about guaranteed to have a little "W" shape in the bottom—I'd even put money on information technology.

Why to Use a Articulation Filter

This method wasn't only popularized because information technology looks absurd, and could represent either "Weed" or "Marijuana" (depending on which manner yous hold it). It's also one of the nigh constructive ways to forbid your filters from getting clogged, and from keeping tiny pieces of cannabis from flying into your oral fissure.

Don't believe me? Take it from Wiz Khalifa.

How to Whorl the Perfect Joint Filter

The methodology behind the "W" shaped joint filter is uncomplicated.

1. Start out with a joint filter tip, which you lot can buy at your local caput shop or online. If you lot don't have access to this, your next best bet is to cut off a rectangle strip from a business organisation card that'due south approximately 1 inch wide and 2 inches long. Recollect that the width of this rectangle volition stop upwards determining how long your filter is, and the length of this rectangle will determine the girth of the filter. So make this rectangle equally large or equally pocket-size as you want, according to how thin, thick, and/or long you want your joint to be.

2. Take your rectangular filter tip and fold a 0.4 – 0.8 of an inch (1mm – 2mm) slice of the cease and so that it creates a small-scale rectangle shape. Keeping that rectangle folded over, fold the filter tip again in the aforementioned way, simply this time fold it in the opposite direction. (If you were to unfold both, you should at present have 2 pocket-size rectangles.) Keep these two folds in place, and fold the filter tip once again in the aforementioned fashion, over again reversing the direction of the fold so that you're folding it on the same side as the very first fold you lot made. If you're looking at the filter tip from a side contour, you lot should now see a "W" shape on one terminate, where i side of the "W" is super long considering of the remaining inch-or-so of filter paper that hasn't yet been folded or rolled.

3. With one mitt, clamp the "W" shape closed. With the other hand, start wrapping all the excess, unfolded filter paper around the "W" shape and then that by the end your filter tip has a "W" shape with a circle effectually it on both ends. You lot can wrap this as tightly or as loosely as you'd like, depending on how big you want the filter to be. The looser y'all roll it, the more the "W" shape will stand out. But since this will too create a larger filter, yous'll desire to use the filter in a larger joint. If you roll information technology tightly, the "West" shape might exist harder, or nearly impossible, to see. Merely rolling information technology tightly like this will also let you to roll a smaller, thinner articulation if that's what you prefer.

4. Coil the filter back and forth betwixt your thumb and forefinger until the filter stays rolled up on its own and doesn't uncoil if you put information technology downwards on the table.

5. Use your new filter to roll a articulation and congratulate yourself on a job well done.

How to Roll a Joint with a Charcoal Filter

The easiest way to do this is to purchase 1 online or from your local headshop and roll information technology into your joint the same as you would whatsoever other type of filter. You could too effort to mode your own charcoal filter if yous take charcoal powder and a thin plastic tube, a few inches long.

1. Roll a joint with a thin filter in the end.

2. Roll another thin filter that can fit within of a thin plastic tube. Put the filter in 1 cease of the plastic tube.

three. Fill up the plastic tube almost all the style to the top with charcoal powder, leaving plenty room in the end then you tin can slide the filter-side of the joint you lot just rolled into the plastic tube. Then, do exactly that: slide the filter-side of the joint into the finish of the plastic tube.

iv. You should now have a joint with a filter, attached to a plastic tube filled with charcoal powder, with another filter at the stop where y'all'll smoke out of.

How to Gyre a Filter Shaped like a Cannabis Leaf

This method of rolling a joint filter is the same idea as the "W" filter, but with more folds.

1. Start out with a joint filter tip, which yous can purchase at your local caput shop or online. The larger the filter tip, the easier this process will be. If you lot don't take admission to this, your side by side best bet is to cut off a rectangle strip from a concern card. (Notation: retrieve the larger the filter tip, the larger the filter will be at the end. The larger the resulting filter, the larger of a joint you'll end upward rolling.) Take your filter tip and outset making folds, the same as is detailed in the "W" shaped filter instructions higher up.

2. While making the start five folds, brand sure the folds get bigger and bigger each time, and so that when you look at the filter paper from a side angle, there are 3 triangular points that get increasingly large. The third point will exist the largest center "leafage" in the cannabis institute shape. Then, brand five more folds, simply this time, brand each fold smaller than the last. One time yous've finished folding, look at the filter newspaper from a side angle again. You should now have v triangular points, with the tallest in the center, flanked on either side by slightly smaller points, and on the very ends, the ii smallest points.

three. Take the outside "walls" of the furthest almost, smallest points, and bring them together so that they touch straight below the largest betoken that'southward acting as the alpine center leaf. You should now see the shape of a cannabis leaf. (Note: While an actual cannabis foliage usually has seven points, yours will only have 5. You could endeavour to make seven points, but it would be difficult.)

4. Carefully coil all the excess filter paper around this foliage shape, the same style you lot did with the "West" shaped filter. This should create a circumvolve around the cannabis leaf shape.

5. Past now, some of your "leaf points" will have probably complanate into each other. To reshape them and so that they one time over again resemble a cannabis leafage, merely take a pin and stick it in betwixt all the points to carefully separate them so that they're no longer touching, but splay outwards in the shape of a cannabis leaf.